C-more micro EA1-S6MLW Manual de usuario Pagina 132
- Pagina / 189
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Check Project Functionality
During a routine maintenance schedule is a good time to check the functionality of your
application, making sure that various areas on different screens do what they were designed to
do. An outline or specification for the application is a useful tool for testing the various aspects
of your application. As a starting point, you may want to run through all the screens to make
sure they are accessible.
If there are any trouble-shooting procedures programmed into the C-more 6” Micro-Graphic
panel application, now is a good time to also check these aids.
Checks from the C-more Micro-Graphic Programming Software
If you have a PC available with the C-more Micro-Graphic Programming Software,
EA-MG-PGMSW, installed, and the panel is connected to the PC, you can check the status of
the panel from the Panel Information window.
The Panel Information window shown below will indicate the panel type, if a keypad bezel has
been installed, the total memory, memory used, free memory, firmware version, mask ROM
version, and the PLC protocol selected for its serial communication ports. The programming
software can also be used to update the panel’s firmware to the latest version.
7–6
Chapter 7: Maintenance
®
7
EA1-MG6-USER-M Hardware User Manual, 1st Ed. Rev C, 09/10
- Hardware User Manual 1
- 6-inch Micro-Graphic Panel 1
- HARDWARE USER MANUAL 3
- WARNING 5
- ADVERTENCIA 6
- AVERTISSEMENT 7
- Marques de commerce 7
- TABLE OF CONT ENTS 9
- Table of Contents 10
- GETTING STARTE D 15
- Conventions Used 17
- Product Overview 18
- Agency Approvals 18
- Part Number Key 19
- Product Label Example: 19
- Quick Start Steps 20
- Chapter 1: Getting Started 21
- Optional Accessory 21
- Enclosure Clearances 24
- *Panel Powered from 27
- AutomationDirect PLC via 27
- Communications Cable 27
- SETUP MENU 28
- Available purchased cables 29
- Available PLC Protocols 29
- DV 1000CBL 30
- SPECIFICATIONS 31
- Available Models 32
- Model Specifications 33
- Model Specifications (cont’d) 34
- Panel Dimensions 35
- Communications Ports 36
- Chemical Compatibility 37
- Chapter 2: Specifications 38
- ACCESSORIES 47
- Accessories 48
- Chapter 3: Accessories 49
- EA-MG-PGM-CBL 52
- Converter Dimensions 52
- USB Connectivity 52
- Converter Status LEDs 52
- EA-MG6-BZ2 54
- Dimensions 54
- Panel Thickness 54
- Panel Cutout 54
- IOIOI – PLC 60
- Clear Screen Overlay 61
- INSTALLATION & WIRING 63
- Safety Guidelines 64
- MODEL EA1 S6M W 66
- Wiring Guidelines 67
- Wiring Guidelines (cont’d) 68
- 50 feet [15.0 m] Maximum 69
- SYSTEM SETUP SCREENS 71
- C-more 6” 73
- Micro-Graphic 73
- Setup Menu 75
- Information Menu 76
- Setting Menu 77
- Setting – LCD Contrast 77
- Setting – Beep 80
- Setting – Calibration 81
- Are you sure you 82
- No[F1] / Yes[F5] 82
- Setting – Hourglass 83
- Setting – Rotation 84
- Test Menu 85
- LOOP BACK TEST 86
- TEST MENU 86
- Test Menu – PLC Enquiry Test 87
- Test Menu – Buzzer Test 87
- Test Menu - Touch Panel Test 88
- PLC COMMUNICATIONS 89
- Introduction (cont’d) 91
- DL06 PLC 92
- CLICK PLC 92
- AutomationDirect CLICK PLC: 94
- Example: 96
- RJ12 - 6 pin 97
- K-sequence 98
- Chapter 6: PLC Communications 100
- Allen-Bradley PLCs 101
- Cables from AutomationDirect 103
- CLICK & Direct LOGIC: 105
- Direct LOGIC: 105
- Allen-Bradley: 109
- Mitsubishi: 112
- Diagram 1 114
- Diagram 2 114
- Diagram 3 115
- Diagram 4 115
- Diagram 5 116
- Diagram 6 116
- Diagram 7 117
- Diagram 8 117
- Diagram 9 118
- Diagram 10 118
- Diagram 11 119
- Diagram 12 119
- Diagram 13 120
- Diagram 14 120
- Diagram 15 121
- Diagram 16 121
- MA IN TENA NCE 127
- UTOMATIONDIRECT PLC’s 128
- Check Physical Conditions 129
- Chapter 7: Maintenance 130
- Cleaning the Display Screen 131
- Check Project Functionality 132
- TROUBL ESHOOT ING 135
- Troubleshooting 136
- Display is Dim 137
- No User Program 137
- Updating Firmware 138
- Chapter 8: Troubleshooting 139
- Panel & PLC Error Codes 142
- Panel Errors 143
- Electrical Noise Problems 144
- REPLACEMENT PARTS 145
- Replacement Parts Overview 146
- Replacement Parts 146
- Chapter 9: Replacement Parts 147
- APPENDIX 149
- Introduction 150
- AutomationDirect CLICK 152
- Modicon Modbus RTU 152
- Entivity Modbus RTU 152
- Panel Error Code 153
- P499 Hex Value 153
- Description 153
- P499: Recv. Err Code F017 154
- P499: Recv. Err Code 020C 159
- P499: Recv. Err Code 0016 171
© 2020, manymanuals.es. Todos los derechos reservados | 0.032 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales